How to Make a Sploof: DIY Smoke Filter

Looking for a way to mask the smell while smoking? Then you need a “Sploof”! A Sploof is a device that helps filter out unpleasant odors from a smoking session. It’s a simple device that uses household materials and is easy to make. In this article, we’ll show you a simple way to make your own Sploof!

A Sploof is a must-have item for any smoker if you want to keep your smoking discreet and undetectable. This device is perfect for those who live with non-smokers or in a shared apartment. The Sploof works by neutralizing the smell of smoke that comes out while you exhale. In short, it’s a DIY air-freshener designed to mask the smell and leave the room smelling pleasant. So, let’s dive into how to make one at home!

Introduction

If you’re a smoker or enjoy taking a hit every once in a while, you’re probably familiar with the tell-tale smell that comes along with it. Whether it’s to avoid attention from family members or coworkers, making a sploof is a way to help mask that smell and make your smoking sessions a bit more discreet.

In this article, we’ll take you through the steps of creating your very own sploof, a device that diffuses the smell of smoke to help you smoke in peace.

1. The ingredients you’ll need
Before you get started, you’ll need some supplies on hand. You’ll need a cardboard tube, such as a used toilet paper or paper towel roll. You’ll also need some fabric softener sheets, a pair of scissors, and some tape.

2. Cutting the cardboard tube
Take your cardboard tube and cut it to the desired length. Depending on how big you want your sploof to be, you can cut it to fit your preference.

3. Stuff the tube with fabric softener sheets
Take your fabric softener sheets and stuff them inside the cardboard tube. The number of sheets you’ll need depends on the size of the sploof you are making.

4. Secure the sheets in place
After you’ve stuffed the tube with fabric softener sheets, use tape to secure the ends of the sheets to the cardboard.

5. Add a cover
Take another fabric softener sheet and cover one end of the cardboard tube. Use tape to secure the sheet in place.

6. Test your sploof
Once you’ve created your sploof, test it out by exhaling some smoke into it and seeing if the smell is reduced or masked altogether.

7. Keeping your sploof fresh
Over time, the fabric softener sheets can become less effective at diffusing the smell of smoke. To keep your sploof fresh, you can replace the sheets inside with new ones as needed.

8. Additional sploof tips
If you want to take your sploof to the next level, you can customize it with other items such as activated charcoal or essential oils to add an additional layer of odor control.

9. Other ways to mask smoke smells
Aside from making a sploof, there are other ways to mask the smell of smoke. You can try opening a window or using air fresheners to help mask the smell.

10. Conclusion
By following these simple steps, you can make your own sploof to help diffuse the smell of smoke and make your smoking sessions a bit more discreet. With a bit of creativity and customization, you can take your sploof to the next level and enjoy your smoking sessions without anyone knowing.

How to Make a Sploof: The Materials

Now that you have a good understanding of what a sploof is and how it works, it’s time to gather your materials. Here are the things you will need to make your sploof:

1. A plastic bottle or container with a lid: This will be the main body of your sploof. You can use any size of plastic bottle or container as long as it has a lid. However, bigger bottles are preferable as they will have more space for activated carbon.

2. Scissors or a knife: These will be used to cut and shape the plastic bottle or container.

3. Activated carbon: This is the key ingredient that will remove the odor from your smoke. You can find activated carbon at most pet stores or aquarium supply stores.

4. Dryer sheets: These will be used to filter the smoke and leave your room smelling fresh.

5. Rubber band or tape: This will be used to keep the dryer sheets in place on the sploof.

6. A pen or marker: This will be used to mark and measure your bottle or container for cutting.

7. A drill or sharp object to make holes: This will be used to make holes on the bottom and top of the bottle.

8. Scented oils or sprays (optional): These will be used to add a pleasant scent to the air.

Step-By-Step Guide to Making a Sploof

Now that you have all your materials ready, it’s time to start making your sploof. Follow these step-by-step instructions to make your sploof:

1. Begin by cleaning and drying out your plastic bottle or container.

2. Using your pen or marker, mark two holes at the bottom of the bottle/container, and two holes at the top. The holes should be of equal size and be placed on opposite sides of the bottle.

3. Use your drill or sharp object to poke holes through the marked spots at the bottom and top of the bottle/container.

4. Take the activated carbon and fill the bottle/container up until it is about two-thirds full.

5. Place a few dryer sheets on top of the activated carbon.

6. Use your rubber band or tape to hold the dryer sheets in place.

7. Using your scissors or knife, cut off the bottom of the plastic bottle or container.

8. Take the lid off and discard it. Cut off the top of the plastic bottle/container. You should now have a hollow tube of plastic.

9. Take some more dryer sheets and stuff them into the open end of the tube.

10. Use your rubber band or tape to hold the dryer sheets in place.

That’s it! You have now successfully made your own sploof. Congratulations! This is an easy and cost-effective way to filter out the smoke and keep your room smelling fresh. Remember to refresh the activated carbon every few weeks to ensure the sploof keeps working effectively.

Materials Needed to Make a Sploof

Making a sploof is an affordable and straightforward process that involves using readily available materials. In this section, we will outline the essential materials that you will need to make a sploof.

Step 1: Gather Materials

The first step in making a sploof is to gather the necessary materials. Check your bathroom for an empty toilet paper roll, grab a few dryer sheets, and find a rubber band, a pair of scissors or a knife, and some tape.

Step 2: Prepare the Dryer Sheets

Next, you need to prepare the dryer sheets for use. Take a few used sheets and fold them in half to form a rectangle. Then, fold the rectangle in half again to form a square. Repeat this process until you have around five or six sheets of folded squares.

Step 3: Insert Dryer Sheets into the Toilet Paper Roll

Now, take the folded dryer sheets and place them inside the toilet paper roll. Push them down into the roll and make sure they are firmly in place.

Step 4: Secure the Dryer Sheets with a Rubber Band

After inserting the dryer sheets into the toilet paper roll, wrap a rubber band around one end of the roll to keep them in place.

Step 5: Cut Holes into the Sploof

Using a pair of scissors or a knife, cut some holes in the other end of the toilet paper roll. You can punch a few small holes or make a larger hole that can accommodate a mouthpiece. The goal here is to create a path for the smoke to travel through the dryer sheets.

Step 6: Add the Final Touches with Tape

Finally, use tape to seal the edges of the sploof. This will ensure that the dryer sheets stay in place and that the smoke passes through them.

In conclusion, making a sploof is an easy process that requires just a few household items. By following these steps, you can easily create a sploof that will help filter out smoke and odor from your smoking sessions. Remember to change the dryer sheets frequently to ensure proper filtration.

Thanks for reading! Whether you’re an experienced smoker or just starting out, making a sploof is a simple and effective way to keep your smoking session discreet. Remember to use these steps and materials to make your sploof and enjoy your smoking without any worry. We hope you found this article helpful and don’t forget to visit our website again for more interesting topics. Happy smoking!